AR-15 and M-16 Show And Tell

[Trigger Time]

What rail covers are on your fortis rail? I need some

 

[wsenefeld]

What rail covers are on your fortis rail? I need some

Rail covers are by KAC. Comes in a 7 pack and I happen to have 3 left. If you want them, send me a PM and I'll see if the gf can't ship them out tomorrow.

 

[Trigger Time]

Rail covers are by KAC. Comes in a 7 pack and I happen to have 3 left. If you want them, send me a PM and I'll see if the gf can't ship them out tomorrow.

YOU ARE AWESOME!! Thank you!

 

[caulfieldian]

Lightweight AR



Finished a "lightweight" upper build today. Once the ATF clears the lower waiting on it it will weigh a bit over 6 pounds (I think) including the scope.

 

[THE BIG SITT]

Assuming I am reading this right, you're saying that lower hasn't been SBRed yet, and that barrel is <16"? If so, delete the picture ASAP.

 

[caulfieldian]

No, this is an SBR lower. The upper for it is gray as well, hence the mismatching colors.

The lower that is waiting on a stamp is sitting in a safe, still stripped.

 

[TheUziButton]

[video=youtube_share;gk1kJpFZTjY]http://youtu.be/gk1kJpFZTjY[/video]

[video=youtube_share;DFkuvsoxOZM]http://youtu.be/DFkuvsoxOZM[/video]

 

[TheUziButton]

[video=youtube;qj80KwdmnNc]http://www.youtube.com/watch?v=qj80KwdmnNc[/video]

 

[SHCdvldg]

This is an American Defense UIC Mod 2, 16", Grey Cerakote finish with a 13.5" M-LOK rail. I recently ran this gun at the Costa Ludus ICET class in Wyoming, consistently hitting B/C Zone steel out to 720yds in adverse weather conditions as well as print consistent sub-MOA groups at 100yds with 55gr Black Hills .223Rem. The rifle ran flawlessly throughout the class and was shot mostly suppressed. The ambidextrous make the manual of arms very smooth, efficient and intuitive for both right and left handed shooters with a very short learning curve. For more info or to pick one up for yourself, visit www.ADMfirearms.com and find a dealer near you! a local stocking dealer right here in Indiana is Copper Custom armament in Valparaiso, IN.

 

[JeremiahJohnson]

I posted these over on the thread about Backwoods Hydrographics - they're the ones that dipped the receivers, stock and quadrail for me:

























These are the parts after dipping:

 

[SHCdvldg]

SBR build I recently finished, based on a Form 1-ed PSA "blem" lower.

LMT 10.5" Mk18 upper (1:7, 4150 CMV, Chrome Lined)
Geissele Nitride Super Gas Block/ADM HD gas tube
Surefire SOCOM MB556
Geissele SMR Mk4 M-LOK 9.5"
ADM Enhanced BCG
Springco "RED" Extra power action spring
ADM HD buffer
KAC 300-600m Rear BUIS/Magpul MBUS pro front
Aimpoint COmp M4s in ADM Lower 1/3rd mount
BCM Ambi Gunfighter CH
CMC 2/2 Flat face trigger
Troy Ambi mag release
Magpul BAD lever <-- probably going to ditch this soon

This thing runs so smooth and flat with the spring/buffer/gas port (0.072") sizing/muzzle brake combo. I also ran the upper on a registered full auto lower last week. It was extremely controllable, slower cyclic rate, tons of fun!

 

[INPatriot]

[video=youtube;qj80KwdmnNc]http://www.youtube.com/watch?v=qj80KwdmnNc[/video]

That flat top mount on the carry handle is sharp. What is it?

 

[mammynun]

That flat top mount on the carry handle is sharp. What is it?

Surplus Aimpoint, I got it from INGO member Sheepdog Gear. It balances very well, and the irons are still usable.

 

[Sheepdog Gear]

Surplus Aimpoint, I got it from INGO member Sheepdog Gear. It balances very well, and the irons are still usable.

 

[mammynun]

Surplus Aimpoint, I got it from INGO member Sheepdog Gear. It balances very well, and the irons are still usable.

 

[TheUziButton]

[video=youtube_share;U0M3j9XL-TM]http://youtu.be/U0M3j9XL-TM[/video]

 

[pyzik]

Carbine by David Pyzik, on Flickr

Upgraded stock

Mid Range by David Pyzik, on Flickr

 

[TheUziButton]

[video=youtube_share;uH-rH5Uvf58]http://youtu.be/uH-rH5Uvf58[/video]

 

[ChristianPatriot]

I think I should SBR it.

 

[DriverAndrew]

DPMS with accessories. No complaints